Adder-technology AdderLink iPEPS Manuel d'utilisateur Page 59

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 69
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 58
 




58
Calculating the mask for IP access control
The IP access control function uses a standard IP address and a net mask
notation to specify both single locations and ranges of addresses. In order to
use this function correctly, you need to calculate the mask so that it accurately
encompasses the required address(es).
Single locations
Some of the simplest addresses to allow or deny are single locations. In this case
you enter the required IP address into the ‘Network/Address’ field and simply
enter the ‘Mask’ as 255.255.255.255 (255 used throughout the mask means
that every bit of the address will be compared and so there can only be one
unique address to match the one stated in the ‘Network/Address’ field).
All locations
The other easy setting to make is ALL addresses, using the mask 0.0.0.0 As
standard, the IP access control section includes the entry:
+
0.0.0.0/0.0.0.0
The purpose of this entry is to include all IP addresses. It is possible to similarly
exclude all addresses, however, take great care not to do this as you instantly
render all network access void. There is a recovery procedure should this occur.
Address ranges
Although you can define ranges of addresses, due to the way that the mask
operates, there are certain restrictions on the particular ranges that can be set.
For any given address you can encompass neighbouring addresses in blocks of
either 2, 4, 8, 16, 32, 64, 128, etc. and these must fall on particular boundaries.
For instance, if you wanted to define the local address range:
192.168.142.67 to 192.168.142.93
The closest single block to cover the range would be the 32 addresses from:
192.168.142.64 to 192.168.142.95.
The mask needed to accomplish this would be: 255.255.255.224
When you look at the mask in binary, the picture becomes a little clearer. The
above mask has the form: 11111111.11111111.11111111.11100000
Ignoring the initial three octets, the final six zeroes of the mask would ensure
that the 32 addresses from .64 (01000000) to .95 (01011111) would all be
treated in the same manner. See Net masks - the binary explanation for
details.
When defining a mask, the important rule to remember is:
There must be no ‘ones’ to the right of a ‘zero’.
For instance, (ignoring the first three octets) you could not use a mask that had
11100110 because this would affect intermittent addresses within a range in an
impractical manner. The same rule applies across the octets. For example, if you
have zeroes in the third octet, then all of the fourth octet must be zeroes.
The permissible mask values (for all octets) are as follows:
Mask octet Binary Number of addresses encompassed
255 11111111 1 address
254 11111110 2 addresses
252 11111100 4 addresses
248 11111000 8 addresses
240 11110000 16 addresses
224 11100000 32 addresses
192 11000000 64 addresses
128 10000000 128 addresses
0 00000000 256 addresses
If the access control range that you need to define is not possible using one
address and one mask, then you could break it down into two or more entries.
Each of these entries could then use smaller ranges (of differing sizes) that,
when combined with the other entries, cover the range that you require.
For instance, to accurately encompass the range in the earlier example:
192.168.142.67 to 192.168.142.93
You would need to define the following six address and mask combinations in
the IP access control section:
Network/address entry Mask entry
192.168.142.67 255.255.255.255 defines 1 address (.67)
192.168.142.68 255.255.255.252 defines 4 addresses (.68 to .71)
192.168.142.72 255.255.255.248 defines 8 addresses (.72 to .79)
192.168.142.80 255.255.255.248 defines 8 addresses (.80 to .87)
192.168.142.88 255.255.255.252 defines 4 addresses (.88 to .92)
192.168.142.93 255.255.255.255 defines 1 address (.93)
Vue de la page 58
1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 68 69

Commentaires sur ces manuels

Pas de commentaire

Acer X113H manuales

Manuales del propietario y guías del usuario para Proyectores Acer X113H.
Ofrecemos 9 manuales en pdf Acer X113H para descargar gratis por tipos de documentos: Manual de usuario






Más productos y manuales para Proyectores Acer

Modelos Tipo de documento
P1273 Manual de usuario   Acer P1273 Manuel d'utilisation, 69 paginas
P1276 Manual de usuario          Acer P1276 User Manual, 18 paginas
X1263 Manual de usuario          Acer X1263 User Manual, 18 paginas
X1263N Manual de usuario          Acer X1263N User Manual, 18 paginas
P5205 Manual de usuario   Acer P5205 Manuel d'utilisation, 60 paginas
C205 Manual de usuario          Acer C205 User Manual, 68 paginas
XS-X10 Manual de usuario   Acer XS-X10 Manuel d'utilisation, 62 paginas
X1161Pn Manual de usuario          Acer X1161Pn User Manual, 18 paginas
PE-W30 Manual de usuario   Acer PE-W30 Manuel d'utilisation, 62 paginas
P1500 Manual de usuario          Acer P1500 User Manual, 19 paginas
H9500BD Manual de usuario   Acer H9500BD Manuel d'utilisation, 63 paginas
S1200 Manual de usuario   Acer S1200 User Manual, 2 paginas
K137 Manual de usuario          Acer K137 User Manual, 18 paginas
H6510BD Manual de usuario          Acer H6510BD User Manual, 20 paginas
P1283 Manual de usuario   Acer P1283 Manuel d'utilisation, 69 paginas
P7605 Manual de usuario          Acer P7605 User Manual, 18 paginas
XS-X13E Manual de usuario   Acer XS-X13E Manuel d'utilisation, 61 paginas
K330 Manual de usuario   Acer K330 Manuel d'utilisation, 27 paginas
K130 Manual de usuario   Acer K130 Manuel d'utilisation, 28 paginas
PD523 Manual de usuario   Acer PD523 Manuel d'utilisation, 59 paginas